Gbit Tech (818) 809-6743 SIGHT
C-7 #1050088  ·  Liability insured  ·  UniFi Certified PartnerNever the cheapest. Built to last.

WiFi Installation & Wireless Networks in Los Angeles

We install UniFi WiFi that covers the whole property, without dead spots.

White UniFi access point on a conduit hanger below a wood beam

WiFi installation for homes and offices

A good WiFi installation gives every room, the yard and the garage a strong signal, not just the room with the router. We place wired access points from your floor plan and the building materials, and we build the network on UniFi.

Not sure where the signal is weak? Add a WiFi site survey before we install.

At Gbit Tech LLC, we deploy Ubiquiti UniFi wireless systems built on WiFi 7 access points (U7 Pro XGS for ceilings, U7 Pro Wall for rooms, U7 Pro Outdoor for patios and yards), and mesh configurations. We plan access point placement from the layout of the property, and a professional WiFi site survey with heat maps and spectrum analysis is available as its own service or together with an installation. Request an estimate.

We build networks for high-bandwidth use and IoT devices that you can add to later.

Measure your WiFi before you change it

We survey on site with an Ekahau Sidekick 2 and deliver coverage heat maps, an access point plan, and a written report. Available on its own, or as part of an installation when it is in scope.

About WiFi site surveys

What we install

Coverage planned for the property, not guessed.

Access point placement

Access points placed from the layout of the property.

Channel planning

Channel planning that accounts for interference in dense areas.

Site surveys

A professional WiFi site survey, with heat maps and spectrum analysis, is available on its own or with an installation.

Install and tune

Installation, configuration and tuning.

How we plan WiFi

Walls, floors and glass decide WiFi coverage more than square footage does. Stucco over wire lath, concrete, stone and low-e windows all cut the signal, especially at 5 GHz and 6 GHz. So we start with the floor plan and a walk through the building, and place access points where they can reach the rooms people actually use.

Every access point gets its own CAT6A cable back to a UniFi switch, which powers it over PoE. We avoid wireless mesh between access points when a wire can be pulled, because a wired link is faster and steadier. After install we set channels and power, put guests and smart-home devices on their own networks, and check coverage by walking the property.

For a large property or a hard layout, a measured plan beats a guess. Depending on the deployment, we do a pre-install site survey and Ekahau report, which gives you heat maps and an access point plan before anything is installed. After install, we always check coverage by walking the property.

Questions to settle before we start

  • How many people and devices are on the network at the busiest time?
  • Which rooms and outdoor areas need strong signal, and which can do with less?
  • Where does internet service enter the building, and where can the gateway and switch live?
  • Is there cable in the walls already, and what kind?
  • Do you want guests, staff, kids and smart devices on separate networks?

Mistakes we see with WiFi

  • One strong router in a closet. The signal drops with every wall, and the far rooms suffer.
  • Adding access points with no plan. Radios close together on the same channels interfere and can make things worse.
  • Hiding an access point in a cabinet or behind a TV. It belongs in the open, on a ceiling or high on a wall.
  • Turning transmit power to the maximum. Your phone hears the access point, but the access point cannot hear the phone back.
  • Reusing old cable without testing it.

Where we install

We install WiFi across Los Angeles and the Valley, including Sherman Oaks, Calabasas and Woodland Hills, Santa Monica and the Westside and Malibu. For access point choices, read WiFi 7 with UniFi U7 access points. Want a ballpark for the equipment and installation first? Sketch your property in Sight.

UniFi access point on a ceiling
In-wall access point beside an outlet
Outdoor access point on a stucco wall
UniFi U7 Pro XGS access point on a wood beam
White UniFi outdoor access point on a cedar shingle wall

How we work

From walkthrough to a live on-prem system.

  1. 01

    WALK

    We map the site and confirm the brief.

  2. 02

    DESIGN

    We plan coverage, pathways, and hardware.

  3. 03

    INSTALL

    We pull cable and label every run.

  4. 04

    HAND OFF

    We walk you through the finished install.

WiFi installation questions

How much does WiFi installation cost?

It depends on the size and layout of the property, the building materials, and whether cable is already in the walls. Read what drives installation cost, then get a ballpark in Sight.

How many access points does a house need?

It depends on the layout and the walls, not the square footage. Stucco, concrete, stone and low-e glass block signal, so we plan placement from the floor plan and a walk through the building.

Is wired WiFi better than mesh?

For most properties, yes. When a cable can be pulled, a wired access point is faster and steadier than a wireless mesh link between units.

Why is my WiFi weak in some rooms?

Walls, floors and glass cut the signal, and one router in a closet cannot reach every room. Access points placed around the property fix it better than a stronger router.

Do you do a WiFi site survey?

Yes, for large properties and hard layouts. A WiFi site survey before the install gives you heat maps and an access point plan first.

Good fit
Hospitality and offices

Restaurants, bars, and multi-tenant offices in LA Metro.

Studios

Production studios and content creators in the San Fernando Valley.

Homes

Whole-property WiFi for luxury homes.

How do you plan coverage?

We plan access point placement from the layout of the property. For a measured plan, a professional WiFi site survey with heat maps and spectrum analysis is available on its own or with an installation. Request an estimate to get started.

What about IoT devices and heavy use?

We build networks for both high-bandwidth use and IoT devices, with room to add more.

Do you handle the cabling too?

Yes. Installation, configuration and tuning, including the wiring behind each access point.

How many access points does my property need?

The layout and the materials decide, not the square footage. A house with thick walls can need more access points than an open office of the same size. We plan the count from the floor plan.

Is mesh WiFi good enough?

Mesh is fine when no cable can be run. When one can, a wired access point is faster and steadier, so we plan that first.

Do you work on systems that are not UniFi?

Yes. We are primarily focused on UniFi, and we also service and troubleshoot other systems. Tell us what you have and we will say plainly whether it is worth fixing, keeping or replacing. See other low-voltage work.

What does it cost?

We price the whole project, not the hour or the device, so it depends on the site. Read what drives the cost of a UniFi installation, sketch your property in Sight for a ballpark, then request an estimate.

Ready to scope it?

(818) 809-6743 · office@gbittech.net · LA Metro

Serving all of LA Metro with low-voltage installations.

Request an estimate. Want a ballpark first? Sketch your property in Sight. Curious what moves the price? Read what drives UniFi installation cost.